| 
  • If you are citizen of an European Union member nation, you may not use this service unless you are at least 16 years old.

  • Stop wasting time looking for files and revisions! Dokkio, a new product from the PBworks team, integrates and organizes your Drive, Dropbox, Box, Slack and Gmail files. Sign up for free.

View
 

Linux

Page history last edited by Wesha 9 years, 10 months ago

Here is the lspci output of a SS4200-EHW:

 

debian:/home/user# lspci

 00:00.0 Host bridge: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub (rev 02)
 00:02.0 VGA compatible controller: Intel Corporation 82945G/GZ Integrated Graphics Controller (rev 02)
 00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 01)
 00:1c.2 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 3 (rev 01)
 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01)
 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01)
 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 01)
 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 01)
 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01)
 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1)
 00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01)
 00:1f.2 SATA controller: Intel Corporation 82801GR/GH (ICH7 Family) SATA AHCI Controller (rev 01)
 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01)
 01:00.0 Ethernet controller: Intel Corporation 82573V Gigabit Ethernet Controller (Copper) (rev 03)
 02:00.0 Mass storage controller: Silicon Image, Inc. SiI 3132 Serial ATA Raid II Controller (rev 01)

 

debian:/home/user# lspci -vvv

 00:00.0 Host bridge: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub (rev 02)
       Subsystem: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub
       Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
       Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
       Latency: 0
       Capabilities: [e0] Vendor Specific Information <?>
       Kernel driver in use: agpgart-intel
       Kernel modules: intel-agp
 00:02.0 VGA compatible controller: Intel Corporation 82945G/GZ Integrated Graphics Controller (rev 02) (prog-if 00 [VGA controller])
       Subsystem: Intel Corporation 82945G/GZ Integrated Graphics Controller
       Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
       Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
       Latency: 0
       Interrupt: pin A routed to IRQ 10
       Region 0: Memory at ffa80000 (32-bit, non-prefetchable) [size=512K]
       Region 1: I/O ports at ec00 [size=8]
       Region 2: Memory at e0000000 (32-bit, prefetchable) [size=256M]
       Region 3: Memory at ffa40000 (32-bit, non-prefetchable) [size=256K]
       Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-
               Address: 00000000  Data: 0000
       Capabilities: [d0] Power Management version 2
               Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
               Status: D0 PME-Enable- DSel=0 DScale=0 PME-
       Kernel modules: intelfb
 00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 01) (prog-if 00 [Normal decode])
       Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
       Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
       Latency: 0, Cache Line Size: 32 bytes
       Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
       I/O behind bridge: 0000b000-0000bfff
       Memory behind bridge: ff600000-ff6fffff
       Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
       Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
       BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
               PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
       Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
               DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
                       ExtTag- RBE- FLReset-
               DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
                       RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
                       MaxPayload 128 bytes, MaxReadReq 128 bytes
               DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
               LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 <4us
                       ClockPM- Suprise- LLActRep+ BwNot-
               LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
                       ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
               LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
               SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+
                       Slot #  0, PowerLimit 0.000000; Interlock- NoCompl-
               SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
                       Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
               SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
                       Changed: MRL- PresDet+ LinkState+
               RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
               RootCap: CRSVisible-
               RootSta: PME ReqID 0000, PMEStatus- PMEPending-
       Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
               Address: fee0100c  Data: 41b9
       Capabilities: [90] Subsystem: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1
       Capabilities: [a0] Power Management version 2
               Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
               Status: D0 PME-Enable- DSel=0 DScale=0 PME-
       Kernel driver in use: pcieport-driver
       Kernel modules: shpchp
 00:1c.2 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 3 (rev 01) (prog-if 00 [Normal decode])
       Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
       Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
       Latency: 0, Cache Line Size: 32 bytes
       Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
       I/O behind bridge: 0000c000-0000cfff
       Memory behind bridge: ff700000-ff8fffff
       Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
       Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
       BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
               PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
       Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
               DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
                       ExtTag- RBE- FLReset-
               DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
                       RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
                       MaxPayload 128 bytes, MaxReadReq 128 bytes
               DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
               LnkCap: Port #3, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 <4us
                       ClockPM- Suprise- LLActRep+ BwNot-
               LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
                       ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
               LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
               SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+
                       Slot #  0, PowerLimit 0.000000; Interlock- NoCompl-
               SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
                       Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
               SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
                       Changed: MRL- PresDet+ LinkState+
               RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
               RootCap: CRSVisible-
               RootSta: PME ReqID 0000, PMEStatus- PMEPending-
       Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
               Address: fee0100c  Data: 41c1
       Capabilities: [90] Subsystem: Intel Corporation 82801G (ICH7 Family) PCI Express Port 3
       Capabilities: [a0] Power Management version 2
               Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
               Status: D0 PME-Enable- DSel=0 DScale=0 PME-
       Kernel driver in use: pcieport-driver
       Kernel modules: shpchp
 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01) (prog-if 00 [UHCI])
       Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1
       Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
       Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
       Latency: 0
       Interrupt: pin A routed to IRQ 23
       Region 4: I/O ports at e000 [size=32]
       Kernel driver in use: uhci_hcd
       Kernel modules: uhci-hcd
 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01) (prog-if 00 [UHCI])
       Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2
       Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
       Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
       Latency: 0
       Interrupt: pin B routed to IRQ 19
       Region 4: I/O ports at dc00 [size=32]
       Kernel driver in use: uhci_hcd
       Kernel modules: uhci-hcd
 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 01) (prog-if 00 [UHCI])
       Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3
       Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
       Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
       Latency: 0
       Interrupt: pin C routed to IRQ 18
       Region 4: I/O ports at d880 [size=32]
       Kernel driver in use: uhci_hcd
       Kernel modules: uhci-hcd
 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 01) (prog-if 00 [UHCI])
       Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4
       Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
       Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
       Latency: 0
       Interrupt: pin D routed to IRQ 16
       Region 4: I/O ports at d800 [size=32]
       Kernel driver in use: uhci_hcd
       Kernel modules: uhci-hcd
 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01) (prog-if 20 [EHCI])
       Subsystem: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller
       Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
       Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
       Latency: 0
       Interrupt: pin A routed to IRQ 23
       Region 0: Memory at ffa3f800 (32-bit, non-prefetchable) [size=1K]
       Capabilities: [50] Power Management version 2
               Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
               Status: D0 PME-Enable- DSel=0 DScale=0 PME-
       Capabilities: [58] Debug port: BAR=1 offset=00a0
       Kernel driver in use: ehci_hcd
       Kernel modules: ehci-hcd
 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) (prog-if 01 [Subtractive decode])
       Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
       Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
       Latency: 0
       Bus: primary=00, secondary=03, subordinate=03, sec-latency=32
       I/O behind bridge: 0000f000-00000fff
       Memory behind bridge: fff00000-000fffff
       Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
       Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
       BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
               PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
       Capabilities: [50] Subsystem: Intel Corporation 82801 PCI Bridge
 00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01)
       Subsystem: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge
       Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
       Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
       Latency: 0
       Capabilities: [e0] Vendor Specific Information <?>
       Kernel modules: iTCO_wdt, intel-rng
 00:1f.2 SATA controller: Intel Corporation 82801GR/GH (ICH7 Family) SATA AHCI Controller (rev 01) (prog-if 01 [AHCI 1.0])
       Subsystem: Intel Corporation 82801GR/GH (ICH7 Family) SATA AHCI Controller
       Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
       Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
       Latency: 0
       Interrupt: pin B routed to IRQ 221
       Region 0: I/O ports at e880 [size=8]
       Region 1: I/O ports at e800 [size=4]
       Region 2: I/O ports at e480 [size=8]
       Region 3: I/O ports at e400 [size=4]
       Region 4: I/O ports at e080 [size=16]
       Region 5: Memory at ffa3fc00 (32-bit, non-prefetchable) [size=1K]
       Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
               Address: fee0100c  Data: 41d9
       Capabilities: [70] Power Management version 2
               Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
               Status: D0 PME-Enable- DSel=0 DScale=0 PME-
       Kernel driver in use: ahci
       Kernel modules: ahci
 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01)
       Subsystem: Intel Corporation 82801G (ICH7 Family) SMBus Controller
       Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
       Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
       Interrupt: pin B routed to IRQ 19
       Region 4: I/O ports at 0400 [size=32]
       Kernel driver in use: i801_smbus
       Kernel modules: i2c-i801
 01:00.0 Ethernet controller: Intel Corporation 82573V Gigabit Ethernet Controller (Copper) (rev 03)
       Subsystem: Intel Corporation Device 0000
       Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
       Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
       Latency: 0, Cache Line Size: 64 bytes
       Interrupt: pin A routed to IRQ 220
       Region 0: Memory at ff6e0000 (32-bit, non-prefetchable) [size=128K]
       Region 2: I/O ports at bc00 [size=32]
       Capabilities: [c8] Power Management version 2
               Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
               Status: D0 PME-Enable- DSel=0 DScale=1 PME-
       Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+
               Address: 00000000fee0100c  Data: 41e1
       Capabilities: [e0] Express (v1) Endpoint, MSI 00
               DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
                       ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
               DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
                       RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
                       MaxPayload 128 bytes, MaxReadReq 512 bytes
               DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr+ TransPend-
               LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <128ns, L1 <64us
                       ClockPM- Suprise- LLActRep- BwNot-
               LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
                       ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
               LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
       Kernel driver in use: e1000e
       Kernel modules: e1000e
 02:00.0 Mass storage controller: Silicon Image, Inc. SiI 3132 Serial ATA Raid II Controller (rev 01)
       Subsystem: Intel Corporation Device 3132
       Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
       Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
       Latency: 0, Cache Line Size: 32 bytes
       Interrupt: pin A routed to IRQ 18
       Region 0: Memory at ff8ffc00 (64-bit, non-prefetchable) [size=128]
       Region 2: Memory at ff8f8000 (64-bit, non-prefetchable) [size=16K]
       Region 4: I/O ports at cc00 [size=128]
       Expansion ROM at ff800000 [disabled] [size=512K]
       Capabilities: [54] Power Management version 2
               Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
               Status: D0 PME-Enable- DSel=0 DScale=1 PME-
       Capabilities: [5c] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
               Address: 0000000000000000  Data: 0000
       Capabilities: [70] Express (v1) Legacy Endpoint, MSI 00
               DevCap: MaxPayload 1024 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
                       ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
               DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
                       RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
                       MaxPayload 128 bytes, MaxReadReq 512 bytes
               DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend-
               LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 unlimited, L1 unlimited
                       ClockPM- Suprise- LLActRep- BwNot-
               LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
                       ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
               LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
       Kernel driver in use: sata_sil24
       Kernel modules: sata_sil24

$ sudo lspci -n
00:00.0 0600: 8086:2770 (rev 02)
00:1c.0 0604: 8086:27d0 (rev 01)
00:1c.2 0604: 8086:27d4 (rev 01)
00:1d.0 0c03: 8086:27c8 (rev 01)
00:1d.1 0c03: 8086:27c9 (rev 01)
00:1d.2 0c03: 8086:27ca (rev 01)
00:1d.3 0c03: 8086:27cb (rev 01)
00:1d.7 0c03: 8086:27cc (rev 01)
00:1e.0 0604: 8086:244e (rev e1)
00:1f.0 0601: 8086:27b8 (rev 01)
00:1f.2 0106: 8086:27c1 (rev 01)
00:1f.3 0c05: 8086:27da (rev 01)
01:00.0 0200: 8086:108b (rev 03)
02:00.0 0180: 1095:3132 (rev 01)


 

Comments (18)

crazydave said

at 2:55 am on Oct 1, 2009

I think about to buy a ss4200 and use it with Debian or Ubuntu as OS to run more services then simple NAS (PXE Server ...)
I read about hardware issues with Ubuntu 8.10 and the IDE controller. Can you please post a lscpi -n to get a overview on http://kmuto.jp/debian/hcl/
The Linux section on this pbworks site is not very informative - we should change this ;)

romses said

at 4:05 am on Oct 1, 2009

Hi

I also tried to run debian on the ss4200.
But at the moment, i cannot connect to the nas after booting. The next days, i will get a graphic card, then i will be able to install debian properly.

Frank de Lange said

at 5:03 am on Oct 1, 2009

I'm running Debian (Sid) on a 'converted' (removed all traces of Windows and actually will get/got some money back from Fujitsu, see 'Windows refund on Scaleo 2200 (SS4200-E)') Scaleo 2205 without any problems. I currently use the stock kernel and it just works. As far as I can see there are no hardware issues worth mentioning... I can boot from both the DOM as well as the SATA drives. I have not tried eSATA for lack of such a beast. Booting Debian (or grml which is derived from Debian) from USB sticks is also possible and works without failure. I used a serial console to change the boot order to get the USB stick to boot. What sort of problems are you (afraid of) running into?

crazydave said

at 5:20 am on Oct 1, 2009

Ah I don't have "angst" I just wannt to make sure to be prepared before I start the project ;-)
And this is the first site where I found something about the SS4200 and Linux - all other sites speak about FreeNas or OpenNAS. But these OS are very limited to add more services like mmmh PXE-Server etc...

Frank de Lange said

at 5:22 am on Oct 1, 2009

BTW, I just entered the SS4200 on http://kmuto.jp/debian/hcl/

The results were 'all OK' but I do not see the machine in the list yet. If you want to try for yourself you'll find the output for 'sudo lspci -n' in the article these comments are attached to.

Dave Hansen said

at 5:47 am on Oct 1, 2009

I got Ubuntu running on mine with a serial console. Works great. I actually did the install under qemu/kvm first, though to sort out the bugs, then stuck it on an IDE drive and replaced the DOM.

romses said

at 2:48 pm on Oct 1, 2009

I Tried it quite simular, but i used Virtualbox to install Debian Lenny on my 4GB CF card. But after inserting and booting it, i cannot connect to my ss4200.

Frank de Lange said

at 3:58 pm on Oct 1, 2009

Does the network come up? It sounds to me like it doesn't. Can you ping it? Do you have a router to supply it with an IP address, or did you configure it for a static IP? What is in your /etc/network/interfaces file?

The ethernet controller in this thing is nothing special: an Intel 82573V which should work with just about any 2.6.x kernel using the e1000e driver (but see http://lwn.net/Articles/278016/ for some potential pitfalls).

romses said

at 4:19 pm on Oct 1, 2009

I configured the network as a dhcp client, but it does not get a IP address.
At my second try, i configured a static IP, but with the same results.

crazydave said

at 4:31 pm on Oct 1, 2009

Wow! Thanks for the great replies!
I think I start at first only with 2 1TB HDDs and Raid1 and I may add a few months later 2 1TB HDDS and start a Raid5
Next question:
- how do you control the Raid on the SS4200? Is it controlled via BIOS or via the OS? I never did this before ;)

Cheers,
David

romses said

at 4:38 pm on Oct 1, 2009

The Raid is a software raid

Frank de Lange said

at 4:49 pm on Oct 1, 2009

romses: what is in your /etc/network/interfaces file? Mine is imple:

#/etc/network/interfaces
auto lo
iface lo inet loopback

auto eth0
iface eth0 inet dhcp

romses said

at 4:58 pm on Oct 1, 2009

Exact the same thing as in my /etc/network/interfaces
I think, the correct nic driver could not be loaded, or the boot process is interrupted before initializing the network

H2O said

at 4:56 am on Oct 2, 2009

Here is my way how I installed Debian 5 on SS4200-E. Maybe it's for one of you helpfull.
I prepaired a PATA disc (2.5“) which allready had Grub installed (old notebook disc) and copied 'netboot debian installer' files (initrd.gz, linux) in a subfolder of boot. (/boot/newinstall)
Now I modified the menu.lst and added the console options for serial and created a new first boot entry.
.....
serial --unit=0 --speed=38400 --word=8 --parity=no --stop=1
terminal --timeout=10 serial console
.....
title Debian Installer
root (hd0,0)
kernel /boot/newinstall/linux console=tty0 console=ttyS0,38400n8
initrd /boot/newinstall/initrd.gz
Now I replaced the DOM by the prepaired PATA disc. When you boot up and you are connected via serial link and your terminal emulator uses the right settings (38400,8,n,1) you can do a Debian network installation (Internet access needed). During the installation process you can also repartitioning/format your OS disc – no problem the installer is running in a ramdisc.

romses said

at 1:47 am on Oct 3, 2009

Ok, I solved my Problems!
Debian is running.

I Used a Cardreader to take a look on my CF Card.
There I edit my /boot/grub/menu.lst and added "console=tty0 console=ttyS0,115200n8 " to my kernel line
I also added

serial --unit=0 --speed=115200 --word=8 --parity=no --stop=1
terminal --timeout=10 serial console

to enable the serial concole in Grub.

After that, I was able to determin, what was goinh wrong:
The entry "auto eth0" was missing, so my nic was not started.
Aditionally, i had some hardware issues with my ethernet switch, which made the things more complicated (but this is another story)

At the moment, i am installing Samba, mt-daapd and Twonkymedia and my 6TB Raid5 is syncing (ZZZzzzZZZ...)

Cadre said

at 12:06 pm on Dec 14, 2009

Is there ANYONE out there that is able to boot off the IDE port if the bios configured for "enhanced" mode rather than "compatible"?

I've tried just about every flavor of Ubuntu with the only storage device connected to it being 2.5" PATA drive, yet no version will see the IDE PATA drive.

If I change the bios mode from "enhanced" to "compatible" then even Jaunty will see the PATA drive, but then I'll have no AHCI for the eSata ports.

Any ideas would be appreciated...

CyberLeo said

at 1:12 pm on Dec 14, 2009

I have a CF card (in a DI adapter) that boots fine with GRUB or FreeBSD's bootloader when the bios is set to enhanced mode.

Accessing the card once the kernel has loaded tends to be problematic, though; it's only detected using the generic IDE driver through the legacy ISA ports, and is, in my experience, quite slow.

Cadre said

at 2:29 am on Dec 15, 2009

I was hoping to be able to install Ubuntu to a Pata device CF or otherwise to be assessable via remote console and still have the bios set to enhanced mode. Maybe that's just more trouble than it's worth. I'll look into installing Ubuntu to a USB flash drive and see how that goes.

You don't have permission to comment on this page.